Intel Edison R2 beta firmware boot log です。
******************************
PSH KERNEL VERSION: b0182929
WR: 20104000
******************************
SCU IPC: 0×800000d0 0xfffce92c
PSH miaHOB version: TNG.B0.VVBD.0000000c
microkernel built 10:14:01 Jan 13 2015
******* PSH loader *******
PCM page cache size = 192 KB
Cache Constraint = 0 Pages
Arming IPC driver ..
Adding page store pool ..
PagestoreAddr(IMR Start Address) = 0×04899000
pageStoreSize(IMR Size) = 0×00080000
*** Ready to receive application ***
U-Boot 2014.04 (Jan 30 2015 – 14:15:53)
Watchdog enabled
DRAM: 980.6 MiB
MMC: tangier_sdhci: 0
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
Target:blank
Partitioning already done…
Flashing already done…
GADGET DRIVER: usb_dnl_dfu
reading vmlinuz
5348960 bytes read in 132 ms (38.6 MiB/s)
Valid Boot Flag
Setup Size = 0×00003c00
Magic signature found
Using boot protocol version 2.0c
Linux kernel version 3.10.17-poky-edison+ (sys_dswci@tlsndgbuild004) #1 SMP PREEMPT Fri Jan 30 14:16:35 CET 2015
Building boot_params at 0×00090000
Loading bzImage at address 00100000 (5333600 bytes)
Magic signature found
Kernel command line: “root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=da3656a35eeffe3c5d0973e21496fc52″
Starting kernel …
[ 1.696423] pmic_ccsm pmic_ccsm: Error reading battery profile from battid frmwrk
[ 1.706240] pmic_ccsm pmic_ccsm: Battery Over heat exception
[ 1.706325] pmic_ccsm pmic_ccsm: Battery0 temperature inside boundary
Welcome to Linux!
Expecting device dev-ttyMFD2.device…
Expecting device sys-subsystem-net-devices-wlan0.device…
[ OK ] Reached target Remote File Systems.
Expecting device dev-disk-by\x2dpartlabel-factory.device…
Expecting device sys-subsystem-net-devices-usb0.device…
[ OK ] Reached target Paths.
[ OK ] Set up automount Arbitrary Executable File Formats F…utomount Point.
[ OK ] Reached target Swap.
[ OK ] Set up automount boot.automount.
[ OK ] Created slice Root Slice.
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Created slice User and Session Slice.
[ OK ] Created slice System Slice.
Starting Create list of required static device nodes…rrent kernel…
Starting Apply Kernel Variables…
Starting udev Coldplug all Devices…
Starting Journal Service…
[ OK ] Started Journal Service.
Mounting Debug File System…
Starting Load Kernel Modules…
Mounting POSIX Message Queue File System…
[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems…
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-getty.slice.
Mounting Temporary Directory…
[ OK ] Set up automount home.automount.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ OK ] Mounted Temporary Directory.
[ OK ] Started Create list of required static device nodes …current kernel.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Load Kernel Modules.
Mounting FUSE Control File System…
Mounting Configuration File System…
Starting Load/Save Random Seed…
Starting Create Static Device Nodes in /dev…
[ OK ] Mounted Configuration File System.
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager…
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile…
[ OK ] Mounted /var/volatile.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Reached target Local File Systems.
Starting Trigger Flushing of Journal to Persistent Storage…
Starting Create Volatile Files and Directories…
[ OK ] Created slice system-systemd\x2dfsck.slice.
Expecting device dev-disk-by\x2dpartlabel-home.device…
[ OK ] Started Trigger Flushing of Journal to Persistent Storage.
[ OK ] Found device /dev/ttyMFD2.
[ OK ] Found device /dev/disk/by-partlabel/factory.
Mounting Mount for factory…
[ OK ] Found device /dev/disk/by-partlabel/home.
Starting File System Check on /dev/disk/by-partlabel/home…
[ OK ] Mounted Mount for factory.
[ OK ] Reached target Sound Card.
[ OK ] Started File System Check on /dev/disk/by-partlabel/home.
Mounting /home…
[ OK ] Found device /sys/subsystem/net/devices/wlan0.
[ OK ] Found device /sys/subsystem/net/devices/usb0.
[ OK ] Mounted /home.
[ OK ] Created slice system-systemd\x2drfkill.slice.
Starting Load/Save RF Kill Switch Status of rfkill2…
Starting Load/Save RF Kill Switch Status of rfkill0…
Starting Load/Save RF Kill Switch Status of rfkill1…
[ OK ] Started Create Volatile Files and Directories.
[ OK ] Started Load/Save RF Kill Switch Status of rfkill2.
[ OK ] Started Load/Save RF Kill Switch Status of rfkill0.
[ OK ] Started Load/Save RF Kill Switch Status of rfkill1.
[ 7.914319] systemd-fsck[159]: /dev/mmcblk0p10: recovering journal
[ 7.951288] systemd-fsck[159]: /dev/mmcblk0p10: clean, 877/152608 files, 31363/610299 blocks
Starting Network Time Synchronization…
Starting Update UTMP about System Boot/Shutdown…
[ OK ] Started Network Time Synchronization.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
Starting Restore Sound Card State…
[ OK ] Listening on sshd.socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Watchdog sample daemon…
[ OK ] Started Watchdog sample daemon.
Starting Edison PWR button handler…
[ OK ] Started Edison PWR button handler.
Starting Bluetooth rf kill event daemon…
[ OK ] Started Bluetooth rf kill event daemon.
Starting Daemon to load edison mcu app binary…
[ OK ] Started Daemon to load edison mcu app binary.
Mх�ѥ����A��������cK�K{s�Kcc+��C˛KcK##�+����F���L��VRL mapped to 0xff213000
App size = 11484 bytes
App Authentication feature is disabled!
Resetting IPC
*** Ready to receive application ***
Starting Daemon to handle arduino sketches…
[ OK ] Started Daemon to handle arduino sketches.
Starting Daemon to reset sketches…
[ OK ] Started Daemon to reset sketches.
Starting Permit User Sessions…
Starting D-Bus System Message Bus…
[ OK ] Started D-Bus System Message Bus.
Starting Network Service…
Starting Login Service…
Starting Crashlog service…
[ OK ] Started Crashlog service.
Starting Cleanjournal service…
[ OK ] Started Cleanjournal service.
[ OK ] Started Restore Sound Card State.
[ OK ] Started Permit User Sessions.
[ OK ] Started Login Service.
Starting Daemon to receive the wpa_supplicant event…
[ OK ] Started Daemon to receive the wpa_supplicant event.
Mounting Arbitrary Executable File Formats File System…
Starting Serial Getty on ttyMFD2…
[ OK ] Started Serial Getty on ttyMFD2.
Starting Getty on tty1…
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
Starting PulseAudio Sound System…
[ OK ] Mounted Arbitrary Executable File Formats File System.
[ OK ] Started Network Service.
[ OK ] Reached target Network.
Starting Intel_XDK_Daemon…
[ OK ] Started Intel_XDK_Daemon.
Starting Zero-configuration networking…
Starting Mosquitto – lightweight server implementati…SN protocols…
Starting Network Name Resolution…
Starting Daemon to receive the wpa_supplicant event…
[ OK ] Started Daemon to receive the wpa_supplicant event.
Starting File System Check on /dev/disk/by-partlabel/boot…
[ OK ] Started Network Name Resolution.
[ OK ] Started WPA supplicant service.
[ OK ] Started Mosquitto – lightweight server implementatio…T-SN protocols.
[ OK ] Started Zero-configuration networking.
[ 11.206590] systemd-fsck[269]: dosfsck 2.11, 12 Mar 2005, FAT32, LFN
[ 11.208982] systemd-fsck[269]: /dev/mmcblk0p7: 5 files, 2700/2931 clusters
[ OK ] Started File System Check on /dev/disk/by-partlabel/boot.
[ OK ] Started PulseAudio Sound System.
Stopping Daemon to receive the wpa_supplicant event…
[ OK ] Stopped Daemon to receive the wpa_supplicant event.
Starting Daemon to receive the wpa_supplicant event…
[ OK ] Started Daemon to receive the wpa_supplicant event.
Starting Bluetooth service…
Mounting /boot…
Starting The Edison status and configuration service…
[ OK ] Started The Edison status and configuration service.
[ OK ] Reached target Multi-User System.
[ OK ] Mounted /boot.
[ OK ] Started Bluetooth service.
Poky (Yocto Project Reference Distro) 1.6.1 redbull ttyMFD2
redbull login: